Home Assistant¶

This page lets you control AWTRIX from Home Assistant. Once you connect AWTRIX to your MQTT broker and switch on discovery, it appears as one device with lights, selects, buttons and sensors. You do not write any YAML.

How it behaves¶

AWTRIX never talks to Home Assistant directly. Everything goes through your MQTT broker. With discovery on, AWTRIX announces itself each time it connects to the broker, as one device whose entities match its hardware. Every entity reads and writes the ordinary MQTT topics of AWTRIX, so automations you built on plain MQTT keep working. AWTRIX reads the broker settings once, at start-up, so a change to them needs a restart. Switching discovery on or off works at once.

What you need¶

• Home Assistant 2024.11 or newer. Older versions do not understand the discovery format AWTRIX uses and show nothing.
• The MQTT integration set up in Home Assistant and connected to a broker (Mosquitto or similar).
• The broker's address and port, reachable from the Wi-Fi network AWTRIX is on.
• The IP address of your AWTRIX. If you do not have it, see Find your clock.

Enable discovery¶

In the web UI:

1. Open the System tab and go to the MQTT section.
2. Switch on Enable MQTT and enter the broker's address and port. Add a username and password if your broker needs them.
3. Switch on HA discovery. Leave HA prefix empty unless your Home Assistant uses a different discovery prefix.
4. Save, then press Reboot now in the reminder. The broker connection is read once at start-up.

Over the API, one call switches MQTT on, sets the broker and turns discovery on:

curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"mqttEnabled":true,"mqttHost":"192.168.1.10","mqttPort":1883,"haDiscovery":true}'

If your broker needs a login, add it:

curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"mqttEnabled":true,"mqttHost":"192.168.1.10","mqttPort":1883,
       "mqttUser":"awtrix","mqttPass":"secret","haDiscovery":true}'

Then restart, because the broker connection is read once at start-up:

curl -X POST http://<awtrix-ip>/api/v1/device/reboot

PUT /api/v1/system changes only the keys you send. Everything else stays as it is. Always send Content-Type: application/json. Without it, curl -d marks the body as a form, and AWTRIX refuses the PUT (Content-Type). Every broker and discovery field, with its default and whether it needs a restart, is in System configuration → MQTT and Home Assistant.

A few seconds after AWTRIX reaches the broker, a device named after your hostname (or AWTRIX NG if you never set one) appears under Settings → Devices & Services → MQTT.

Switching haDiscovery on or off later needs no restart. If AWTRIX is connected, the change takes effect at once. Otherwise it takes effect the next time AWTRIX connects.

Verify it worked¶

The fastest check is on the broker. Watch the discovery topic:

mosquitto_sub -h 192.168.1.10 -t 'homeassistant/device/+/config' -v

One retained message arrives when AWTRIX connects. It describes the whole device with every entity. If nothing shows up, check that mqttHost is set and that AWTRIX is connected: <P>/availability should read online.

<P> in the topics on this page is your mqttPrefix. If you left it empty, it is AWTRIX's own uid, the 12-character MAC address.

What lands in Home Assistant¶

Every board gets 19 entities. More appear only when the hardware is there. A board with a battery pin, a light sensor and a temperature/humidity sensor gets 26 entities. A BME280 or BMP280 adds Pressure on top. A board that can make sound adds four more, and a fifth when it plays radio.

Which of the conditional ones appear depends on the board:

• Brightness mode and Light level need a light-sensor pin (pinLdr).
• Temperature, Humidity and Pressure appear for what the detected sensor measures: temperature on any sensor, humidity on a humidity-capable part, pressure only on a BME280 or BMP280. A board without a sensor gets none of them.
• Battery, Battery voltage and Low battery need a battery pin (pinBattery).
• Volume, App volume, Alert volume and Stop sound need a sound output: a buzzer, a speaker or a DFPlayer. Radio volume also needs internet radio.

Nothing is announced for hardware that is not there, so no entity sits at unknown waiting for a value that never arrives.

Every entity points at the ordinary <P>/cmd/... and <P>/state/... topics, so an automation you built against plain MQTT keeps working once you turn discovery on. The full per-entity list, with the topic each one reads and writes, is Entity set.

What each entity does¶

Matrix (light)¶

The display itself, with brightness and RGB.

While auto-brightness is on, the display follows the light sensor. See Brightness mode and Brightness & sensors.

Indicator 1 / 2 / 3 (light)¶

Three RGB-only lights for the small pixel groups on the display's right edge: a corner for Indicator 1 (top) and Indicator 3 (bottom), a short bar in the middle for Indicator 2. Turning one on with the toggle makes it white. Use the color picker for any other color.

Switching an indicator or changing its color in Home Assistant gives a steady light. blinkMs and fadeMs have no entity. Set them with the indicators/<id> command topic.

Brightness mode (select)¶

Manual or Auto. It sets autoBrightness. Set it to Manual before you expect the Matrix brightness slider to do anything. It appears only on a board with a light sensor. Without one, the slider always sets the display.

Transition effect (select)¶

The 22 transition names, for example Random, Slide and Ripple. It sets transitionEffect and takes the same names as the HTTP and MQTT APIs. What each one looks like: Visual reference: Transitions.

Transition (switch)¶

It sets autoTransition. On, the apps take turns by themselves. Off, the rotation stops and the app changes only when you press a button or send a command.

Volume, Radio volume, App volume, Alert volume (number)¶

Four sliders from 0 to 100 %, in steps of 5. They set the mixer of the clock:

A change from the web UI shows here at once.

Buttons (button)¶

Pressing one acts at once:

Sensors¶

Read-only values. Everything that comes from <P>/state/device refreshes every statsInterval, 10 seconds by default. Current app and the entities that show a setting update the moment the value changes. Matrix power and the indicator lights are published again as soon as they change too, so they do not lag behind the display.

Low battery (binary_sensor)¶

On a battery board, ON once the charge drops below lowBatteryThreshold, a percentage. 0 switches the check off. It carries device_class: battery, so Home Assistant shows it as a standard low-battery indicator.

Button left / select / right (binary_sensor)¶

Each follows its physical button: ON while the button is held, OFF on release. They change with every real press and release, so they work directly as automation triggers. They are not retained. AWTRIX sends the current state on every connect.

Sending notifications from Home Assistant¶

There is no notification entity. Send notifications to the command topics instead. They work whether or not discovery is on, and take exactly the same JSON as the HTTP API:

script:
  doorbell:
    sequence:
      - action: mqtt.publish
        data:
          topic: "awtrixNG/cmd/notify"
          payload: '{"text":"Someone is at the door","textColor":"#00FF00","durationMs":8000}'

Replace awtrixNG with your own prefix. Every command topic, its payload and its /result reply: Command topics. The payload keys themselves: App & notification payload.

From a picked device to its topic¶

A blueprint that lets the user pick a device rather than type a prefix reads the MQTT prefix sensor, which carries exactly the <P> that device answers on:

{% set e = device_entities(device_id) | select('search', 'mqtt_prefix') | list %}
{{ states(e[0]) if e else 'unknown' }}

device_id comes from a device selector filtered to integration: mqtt and manufacturer: Blueforcer. The match is on the entity ID, so it breaks if someone renames that entity. Check for unknown and unavailable before you publish.

Switching an app on or off¶

Publish true or false to <P>/cmd/apps/<name>/enabled. Only that app changes. Every other app stays on or off as it is. This automation lets a toggle helper switch one app:

automation:
  - alias: Date app follows its toggle
    triggers:
      - trigger: state
        entity_id: input_boolean.awtrix_date
        to: ["on", "off"]
    actions:
      - action: mqtt.publish
        data:
          topic: "awtrixNG/cmd/apps/Date/enabled"
          payload: "{{ 'true' if trigger.to_state.state == 'on' else 'false' }}"

Use this call, not cmd/apps/order, to switch single apps. The order call sets the complete list of switched-off apps, so every app it does not name is switched on, scripts included. See apps/order.

Triggering on button presses¶

The three button binary_sensor entities work as triggers. To use the topics directly instead: each press is published as the plain string 1, and each release as 0, to <P>/state/buttons/left, /select and /right. These messages are not retained.

automation:
  - alias: "Panel left button pressed"
    trigger:
      - platform: mqtt
        topic: "awtrixNG/state/buttons/left"
        payload: "1"
    action:
      - action: light.toggle
        target:
          entity_id: light.desk_lamp

Watch them to confirm:

mosquitto_sub -h 192.168.1.10 -t 'awtrixNG/state/buttons/+' -v

Details: state topics.

Availability¶

AWTRIX publishes <P>/availability (online / offline, retained) whether or not discovery is on. If AWTRIX drops off the network, the broker sets it to offline by itself. Every Home Assistant entity uses this same topic. An automation keyed on <P>/availability therefore keeps working after you enable haDiscovery.

Inside Home Assistant availability is handled for you: entities go unavailable on their own when AWTRIX drops.

mosquitto_sub -h 192.168.1.10 -t 'awtrixNG/availability' -v

See Availability and LWT.

Changing the discovery prefix¶

Only needed if your Home Assistant uses a discovery prefix other than homeassistant:

curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"haPrefix":"ha-discovery"}'

If AWTRIX is connected, this takes effect at once: the device is removed under the old prefix and announced under the new one. If it is not connected, the change takes effect the next time it reaches the broker.

Turning discovery off¶

curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"haDiscovery":false}'

AWTRIX publishes an empty retained payload to <haPrefix>/device/<uid>/config, which tells Home Assistant to remove the device. This happens at once if AWTRIX is connected, otherwise the next time it reaches the broker. Nothing else changes: <P>/availability and the <P>/cmd/... and <P>/state/... topics behave exactly as before.

To switch MQTT off completely, set mqttEnabled to false and restart:

curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"mqttEnabled":false}'
curl -X POST http://<awtrix-ip>/api/v1/device/reboot

AWTRIX reads mqttEnabled only at start-up, so it keeps talking to the broker until you restart it. The host, username, password, mqttPort, mqttPrefix and haDiscovery all stay saved, so you do not have to type them again when you switch MQTT back on.

Good to know¶

• No device appears. Check that Home Assistant is 2024.11 or newer, that haDiscovery is on, and that haPrefix matches your Home Assistant discovery prefix.
• A yellow dot pulses on the display, or <P>/availability stays empty. AWTRIX cannot reach the broker. See MQTT never connects.
• A change to the broker settings does nothing. AWTRIX reads them only at start-up: restart it.
• Entities are missing. They follow the hardware. See What lands in Home Assistant.
• The brightness slider does not stay where you left it. Auto-brightness is on, and the slider shows the brightness the light sensor sets. Set Brightness mode to Manual first.

Related¶

• MQTT topics: every topic and entity, and what a reply looks like.
• System configuration: every broker and discovery field.
• Device state: what <P>/state/device contains.