Skip to content

Power & battery

This page shows how to read the battery, get a low-battery warning, switch the display off and on, and put the clock to sleep for a while.

How it behaves

Switching the display off only darkens the LEDs. Wi-Fi, MQTT and the apps keep running, and AWTRIX stays reachable over HTTP. Deep sleep is different: it switches the whole clock off for a set time, and nothing reaches it until it wakes. The battery percentage is worked out from the battery voltage alone, so it is an estimate (How the percentage is derived). The low-battery warning stays off until you set a threshold.

Check the battery

All battery values are in the device state:

curl http://<awtrix-ip>/api/v1/device

The battery part of the answer:

{
  "batteryPinMillivolts": 2290,
  "batteryVoltage": 4.1,
  "batteryPercent": 88
}
  • batteryPercent is how full the battery is.
  • batteryVoltage is the battery voltage.
  • batteryPinMillivolts is the voltage the ESP32 measures at its pin. This is lower than the battery voltage. You only need it to calibrate the reading.

The values update every 2 seconds.

The battery values are only there when a battery pin is set (pinBattery is 0 or higher). The default is GPIO 1, so a board with the default wiring has them. With pinBattery: -1 the keys are left out of the answer. They are not shown as 0 or null, and the built-in Battery app leaves the rotation.

Every field: Device state → Battery fields.

Get told when the battery is low

On a board with a battery pin, GET /api/v1/device always has a lowBattery value. lowBattery becomes true when batteryPercent is below lowBatteryThreshold (below, not equal). Set the threshold to a percentage under Low-battery threshold in System → Brightness & sensors of the web UI, or send:

curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"lowBatteryThreshold": 15}'

{
  "batteryPercent": 12,
  "lowBattery": true
}
  • The default is 0, which turns the warning off: lowBattery stays false.
  • lowBattery updates every 2 seconds, like the other battery values, and is left out on a board with pinBattery: -1.
  • In Home Assistant the same warning is the Low battery sensor. See Battery in Home Assistant.

Turn the display off and on

This switches the LEDs off, not the clock. Your brightness and auto-brightness settings stay as they are.

  • On the clock, press the select (middle) button twice quickly. This is the only way to switch the display back on without the network.
  • In the web UI, use the Power switch on the Dashboard.

With the API

Off:

curl -X PATCH http://<awtrix-ip>/api/v1/display \
  -H "Content-Type: application/json" \
  -d '{"power":false}'

On:

curl -X PATCH http://<awtrix-ip>/api/v1/display \
  -H "Content-Type: application/json" \
  -d '{"power":true}'

To see the current state, read power in GET /api/v1/display or matrixPower in GET /api/v1/device. Both are false while the display is off.

Deep sleep

Deep sleep switches the clock off for a fixed time. Unlike switching the display off, AWTRIX is unreachable while it sleeps: no HTTP, no MQTT, no apps.

curl -X POST http://<awtrix-ip>/api/v1/device/sleep \
  -H "Content-Type: application/json" \
  -d '{"durationMs":60000}'
  • durationMs is required: the sleep time in milliseconds, a whole number above 0. There is no value for "sleep forever". 0 is refused with a 422.
  • The clock answers 200 {"ok":true} first and then goes to sleep, so your request gets its answer before the connection drops.
  • All status codes: HTTP API → POST /api/v1/device/sleep.

Two things wake the clock: the timer and the select button. The button only works when pinBtnSelect is on a GPIO that can wake the ESP32, which the default wiring is. If you move it, only the timer wakes the clock. See GPIO & boards → The pin map.

The display goes dark just before the clock sleeps. When it wakes, the ESP32 starts fresh, just like after switching the power off and on: it loads its settings, connects to Wi-Fi, and the display is on again, even if you had switched it off before.

Over MQTT the same command is the device/sleep op. See MQTT topics → Command topics.

Battery in Home Assistant

When the board has a battery pin, Home Assistant gets three entities automatically:

Entity Device class Unit Source
Battery battery % batteryPercent
Battery voltage voltage V batteryVoltage
Low battery battery - lowBattery
  • Low battery only turns on once you set a lowBatteryThreshold above 0 (see Get told when the battery is low).
  • All three are missing on a board with pinBattery: -1.
  • batteryPinMillivolts is not an entity. Read it from GET /api/v1/device when you calibrate.

See Home Assistant.

How the percentage is derived

The clock cannot measure how much charge is left. It works out the percentage from the battery voltage alone, using the typical voltage of a Li-Ion cell at rest:

Battery voltage Shown
4.20 V or more 100 %
3.84 V 50 %
3.73 V 20 %
3.27 V or less 0 %

Between these points the value is interpolated. It never goes above 100 % or below 0 %.

What this means for you:

  • The percentage drops while the display is busy and comes back afterwards. The table is for a battery at rest, and the display draws power in bursts.
  • There is no "time left" estimate. The voltage alone cannot tell you that.
  • Small voltage errors matter. Between 90 % and 20 % the voltage only changes by about 0.4 V. If batteryVoltage is a little off, the percentage is off a lot. Calibrate it as shown below.

Calibrate the divider ratio

This is for boards with a battery pin.

The board lowers the battery voltage before the ESP32 measures it, and batteryDividerRatio says by how much: battery voltage divided by pin voltage. You do not need a meter. A full Li-Ion battery at rest has about 4.2 V, and that is enough.

  1. Charge AWTRIX fully. Then read batteryPinMillivolts:

    curl http://<awtrix-ip>/api/v1/device

  2. Calculate ratio = 4.2 / (batteryPinMillivolts / 1000).

  3. Save it as Battery divider under System → Brightness & sensors in the web UI, or send:

    curl -X PUT http://<awtrix-ip>/api/v1/system \
  -H "Content-Type: application/json" \
  -d '{"batteryDividerRatio":1.79}'

The new ratio applies within 2 seconds, without a reboot.

  • The default is 1.79.
  • Allowed values are 0.1 to 10. Anything else, including 0 or a negative number, is refused with a 422.

Good to know

  • A double press of select does nothing while Block buttons is on. Switch the display with the Power switch or a request instead.
  • Notifications are not shown while the display is off. Add "wakeup": true to show one anyway. See Wake a dark display.
  • A sleeping clock cannot be reached or woken over the network, and you cannot cancel the sleep. Without access to the clock, one hour of sleep means one hour of silence, so try short times first.
  • If batteryVoltage looks wrong, correct batteryDividerRatio, not the percentage. See Calibrate the divider ratio.

Details